PIC18F2610-E/SO【PDF 146/234 页】IC MCU FLASH 32KX16 28SOIC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3878

142页 143页 144页 145页 [146页]147页 148页 149页 150页

2009 Microchip Technology Inc.

DS39636D-page 25

PIC18F2X1X/4X1X

2.0

OSCILLATOR

CONFIGURATIONS

2.1

Oscillator Types

PIC18F2X1X/4X1X devices can be operated in ten

different oscillator modes. The user can program the

Configuration bits, FOSC3:FOSC0, in Configuration

Low-Power Crystal

Crystal/Resonator

High-Speed Crystal/Resonator

HSPLL High-Speed Crystal/Resonator

with PLL enabled

External Resistor/Capacitor with

FOSC/4 output on RA6

RCIO

External Resistor/Capacitor with I/O

on RA6

INTIO1 Internal Oscillator with FOSC/4 output

on RA6 and I/O on RA7

INTIO2 Internal Oscillator with I/O on RA6

and RA7

External Clock with FOSC/4 output

10. ECIO

External Clock with I/O on RA6

2.2

Crystal Oscillator/Ceramic

Resonators

In XT, LP, HS or HSPLL Oscillator modes, a crystal or

ceramic resonator is connected to the OSC1 and

OSC2 pins to establish oscillation. Figure 2-1 shows

the pin connections.

The oscillator design requires the use of a parallel cut

crystal.

FIGURE 2-1:

CRYSTAL/CERAMIC

RESONATOR OPERATION

(XT, LP, HS OR HSPLL

CONFIGURATION)

TABLE 2-1:

CAPACITOR SELECTION FOR

CERAMIC RESONATORS

Note:

Use of a series cut crystal may give a

frequency out of the crystal manufacturer’s

specifications.

Typical Capacitor Values Used:

Mode

Freq

OSC1

OSC2

3.58 MHz

4.19 MHz

4 MHz

15 pF

30 pF

50 pF

15 pF

30 pF

50 pF

Capacitor values are for design guidance only.

Different capacitor values may be required to produce

acceptable oscillator operation. The user should test

the performance of the oscillator over the expected

VDD and temperature range for the application.

See the notes following Table 2-2 for additional

information.

Note:

When using resonators with frequencies

above 3.5 MHz, the use of HS mode,

rather than XT mode, is recommended.

HS mode may be used at any VDD for

which the controller is rated. If HS is

selected, it is possible that the gain of the

oscillator will overdrive the resonator.

Therefore, a series resistor should be

placed between the OSC2 pin and the

resonator. As a good starting point, the

recommended value of RS is 330

Ω.

Note 1: See Table 2-1 and Table 2-2 for initial values of

C1 and C2.

2: A series resistor (RS) may be required for AT

strip cut crystals.

3: RF varies with the oscillator mode chosen.

C1(1)

C2(1)

XTAL

OSC2

OSC1

RF(3)

Sleep

Logic

PIC18FXXXX

RS(2)

Internal

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式